Snorkel Bi-Energy-sn3300 - 4021 Manuel d'utilisateur télécharger pdf

LX Electric & Bi-Energy

Operator Manual

LX Electric & Bi-Energy

SERIAL NO. 3300 TO CURRENT

Safety Rules and Operating Instructions

WARNING

All personnel shall carefully read, understand and follow all safety rules, operating

instructions and the Scaffold Industry Associations MANUAL OF

RESPONSIBILITIES (ANSI A92.6) before operating or performing maintenance on

any UpRight aerial work platform.

SAFETY RULES

NEVER operate the machine within

ten feet of power lines. THIS

MACHINE IS NOT INSULATED.

NEVER elevate or drive elevated on

uneven slopes or soft ground or el-

evate the platform unless the plat-

form is level.

NEVER sit, stand or climb on

guardrail or midrail.

California Proposition 65 Warning

Gasoline and diesel engine exhaust and some of their constituents are known to the State of Califor-

nia to cause cancer, birth defects, and other reproductive harm.

NEVER operate the machine without first surveying the work area for surface hazards such as holes, drop-offs,

bumps and debris.

NEVER operate the machine if all guardrails are not properly in place and secured with all fasteners properly

torqued.

SECURE and lock gate after mounting platform.

KEEP all body parts clear of outriggers when extending or retracting (outrigger equipped machines only).

NEVER use ladders or scaffolding on the platform.

NEVER attach overhanging loads or increase platform size.

MAINTAIN tire pressure at 50 psi. Check daily.

LOOK up, down and around for overhead obstructions and electrical conductors.

DISTRIBUTE all loads evenly on the platform. See the back cover for maximum platform load.

NEVER use damaged equipment. (Contact UpRight for instructions. See toll-free phone number on back cover.)

NEVER change operating or safety systems.

INSPECT the machine thoroughly for cracked welds, loose hardware, hydraulic leaks, damaged control cable,

loose wire connections and wheel bolts.

NEVER climb down elevating assembly with the platform elevated.

NEVER perform service on machine while platform is elevated without blocking elevating assembly.

NEVER recharge battery near sparks or open flame; batteries that are being charged emit highly explosive

hydrogen gas.

AFTER USE secure the work platform against unauthorized use by turning chassis key switch off and removing

key.

NEVER replace any component or part with anything other than original UpRight replacement parts without the

manufacturer's written consent.

1 2 3 4 5 6 ... 11 12

Résumé du contenu

Page 1 - Operator Manual

1LX Electric & Bi-EnergyOperator ManualLX Electric & Bi-EnergySERIAL NO. 3300 TO CURRENTSafety Rules and Operating InstructionsSafety Rules an

Page 2 - Inspection

10NOTES:

Page 3

11Maximum DistributedPlatform Load 2000 lbsor 5 occupantsMaximum side load 300 lbsMaximum DistributedPlatform Load 1500 lbsor 5 occupantsMaximum side

Page 4 - Operation

12067449-001 3/00 DSpecifications*FOR MORE INFORMATIONLocal Distributor:TEL: (800) 926-5438 or (559) 891-5200FAX: (559) 896-9012PARTS: (888) U

Page 5 - Emergency Lowering

2IntroductionThis manual covers Electric and Bi-Energy modelsof the LX Series Work Platforms. Both machinesoperate on a 48 volt battery powered system

Page 6 - Fold Down Guardrails

3NOTE: Bi-Enery machine may be powered bybatteries or by engine. To power the machine byengine, turn platform or chassis key on, pressengine start but

Page 7 - Transporting Work Platform

47. Grasp the control lever so the interlock lever isdepressed (releasing the interlock lever cutspower to controller). Slowly push or pull thecontrol

Page 8 - Maintenance

5Figure 4: Emergency Lowering KnobAfter Use Each Day1. Ensure that the platform is fully lowered.2. Park the machine on level ground, preferablyunder

Page 9 - Routine Service

6Fold Down GuardrailsThis procedure is only for passing through door-ways. Guardrails must be returned to properposition before using the machine.Fold

Page 10

7Figure 8: Transporting Work PlatformTransporting Work PlatformBy Crane1. Secure straps to chassis tie down/lifting lugsonly (Figure 8).By Truck1. Ma

Page 11 - PLATFORM

8MaintenanceNever perform service on the work plat-form in the elevating assembly area whileplatform is elevated without first blockingthe elevating a

Page 12 - FOR MORE INFORMATION

9Routine ServiceUse the following table as a guide for routinemaintenance. Inspection and maintenance shallbe performed by personnel who are trained