Snorkel XRT33-sn2300+ANSI Manuel d'utilisateur télécharger pdf

Safety Rules and Operating Instructions

Operator Manual

WARNING

All personnel shall carefully read, understand and follow all safety rules,

operating instructions, and the Scaffold Industry Association’s MANUAL

OF RESPONSIBILITIES

of ANSI A92.6-1999

before operating or

performing maintenance on any UpRight Aerial Work Platform.

Safety Rules

Never

operate the machine without first surveying the work area for surface hazards such as holes, drop-

offs, bumps and debris.

Never

operate the machine if all guardrails are not properly in place and secured with all fasteners properly

torqued.

Secure

chain or gate across entrance after mounting platform.

Never

use ladders or scaffolding on the platform.

Never

attach overhanging loads or increase platform size.

Look up

, down and around for overhead obstructions and electrical conductors.

Distribute

all loads evenly on the platform. See the back cover for maximum platform load.

Never

use damaged equipment. (Contact UpRight for instructions. See toll-free phone number on back

cover.)

Never

change operating or safety systems.

Inspect

the machine thoroughly for cracked welds, loose hardware, hydraulic leaks, damaged control

cable, loose wire connections and wheel bolts.

Never

climb down elevating assembly with the platform elevated.

Never

perform service on machine while platform is elevated without blocking elevating assembly.

Never

recharge battery near sparks or open flame; batteries that are being charged emit highly explosive

hydrogen gas.

After Use

secure the work platform against unauthorized use by turning key switch off and removing key.

Never

replace any component or part with anything other than original UpRight replacement parts without

the manufacturer’s consent.

California Proposition 65 Warning

Gasoline and diesel engine exhaust and some of their constituents are known to the State

of California to cause cancer, birth defects, and other reproductive harm.

NEVER operate the machine within

ten feet of power lines.

THIS MACHINE IS NOT INSULATED

NEVER elevate the platform or drive

the machine while elevated unless

the machine is on firm level surface.

NEVER sit, stand or climb on

guardrail or midrail.

XRT Series

SERIAL NO. 2300 to Current

1 2 3 4 5 6 ... 15 16

Résumé du contenu

Page 1 - Operator Manual

Safety Rules and Operating InstructionsSafety Rules and Operating InstructionsOperator ManualWARNINGAll personnel shall carefully read, understand and

Page 2 - PERATION

Page 10 XRT Work PlatformFigure 8: Transporting the Work PlatformBY CRANE1. Secure straps to Lifting Lugs only.BY TRUCK1. Maneuver the work platform i

Page 3

Page 11XRT Work PlatformFigure 9: Blocking the Elevating AssemblyBLOCKING ELEVATING ASSEMBLYBRACE INSTALLATION1. Park the work platform on a firm leve

Page 4

Page 12 XRT Work PlatformBATTERY MAINTENANCE Figure 10: Access to BatteryThe battery is located in the slide out tray. The slide out tray is located a

Page 5

Page 13XRT Work Platform066556-0001-Required067841-002#11-RequiredDual Fuel067841-003#11-RequiredDiesel101252-0071-RequiredXRT27101252-0081-RequiredXR

Page 6

Page 14 XRT Work PlatformThe Complete inspection consists of periodic visual and operational checks, along with periodic minor adjustments to assure p

Page 7 - LOWERING KNOB

Page 15XRT Work PlatformPREVENTATIVE MAINTENANCE CHECKLISTPREVENTATIVE MAINTENANCE KEYIntervalDaily=each shift or every day50h/30d=every 50 hours or 3

Page 8 - ERECTION PROCEDURE

1775 Park StreetSelma, California 93662TEL: (800) 926-LIFT or (559) 891-5200FAX: (559) 891-9012Parts FAX: (559) 896-9244066898-00101-00 DLocal Distri

Page 9 - BRAKE RELEASE PUMP

Page 2 XRT Work PlatformThis manual covers all models of the XRT Self Propelled Work Platforms. This manual must be stored on the machine at all times

Page 10 - RANSPORTING

Page 3XRT Work PlatformFigure 1: Chassis Controls15. Turn Platform Controls Key Switch clockwise to ON.16. CHASSIS CONTROLS, Turn the Platform/Chassis

Page 11 - AINTENANCE

Page 4 XRT Work PlatformFigure 3: Platform Controls26. PLATFORM CONTROLS, Turn Plat-form Controls Key Switch clockwise to ON.NOTE: If the engine is co

Page 12

Page 5XRT Work PlatformBefore operating work platform, ensure that the pre-operation safety inspection has been com-pleted, and that any deficiencies

Page 13 - operating the work platform

Page 6 XRT Work PlatformSTEERING1. Turn the Lift/Drive switch to DRIVE.2. Engage the Interlock Switch, push the Steering Switch RIGHT or LEFT to turn

Page 14 - REVENTATIVE

Page 7XRT Work PlatformLOWERING THE PLATFORM1. Turn the Lift/Drive Switch to LIFT. 2. Engage the Interlock Switch and pull back on the Control Handle

Page 15 - HECKLIST

Page 8 XRT Work PlatformFOLD DOWN GUARDRAILSNOTE: When performing the following procedures retain all fasteners.This procedure is only for passing thr

Page 16 - PECIFICATIONS

Page 9XRT Work PlatformAFTER USE EACH DAY1. Ensure that the platform is fully lowered.2. Park the machine on a firm, level surface, preferably under c