Snorkel SPM20-sn00000 Manuel d'utilisateur

1November 2012OPERATORSMANUALPartnumber 511147-000-ENSerial Number 000001 and after

6 SECTION 5 - GENERAL SPECIFICATIONS AND OPERATOR MAINTENANCE 5.1 INTRODUCTION ...

7 1.1 GENERAL SECTION 1. SAFETY PRECAUTIONS This section outlines the necessary precautions for proper and safe machine usage and maintenance. Fo

8 • Read, understand, and obey all applicable employers, local, and governmental regulations as they pertain to operation of the machine. Workplac

9 • When performing welding operations at elevation, precautions must be taken to protect all machine components from contact with weld splatter or

10 Table 1-1. Minimum Safe Approach Distance (M.S.A.D.) VOLTAGE RANGE (PHASE TO PHASE) MINIMUM SAFE APPROACH DISTANCE-Feet (m) 0-50KV 10(3) Over

11 Tipping Hazard • The user should be familiar with the surface before driving. Do not exceed the allowable side slope and grade while driving.

12 • Do not drive at high speeds in restricted or close quarters or when driving in reverse.• Exercise extreme caution at all times to prevent obstacl

13 Warning labels

14

15 WARNING

16

17

18 SECTION 2. PREPARATION AND INSPECTION 2.1 PERSONNEL TRAINING The aerial platform is a personnel-handling device; so it is necessary that it be

19 SUCCESSFULLY COMPLETED THE SERVICE TRAINING FOR THE SPECIFIC PRODUCT MODEL. Table 2-1. Inspection and Maintenance Table TYPE FREQUENCY PRIMERY

20 7. Function Check – Check all machine controls for operation. (See Section 2.5) If optional equipment is installed on this machine refer

21 Figure 2-1. Daily Walk-Around Inspection for SPM20 Machines. 1. Drive and Caster Wheels 2. Base Frame 3. Manual Descent Control Valve 4. Motor

22 NOTE: Ensure Pot-Hole-Protection device is fully engaged (both bars down) when the platform is elevated.b. Ensure that all machine functions are d

23 SECTION 3. MACHINE CONTROLS, INDICATORS ANDOPERATION Table 3-1 Machine Operating SpecificationsSPM20Maximum Occupants:1Maximum Work Load (Capacity)

24 3.1 GENERAL IMPORTANT THE MANUFACTURER HAS DIRECT CONTROL OVER MACHINE APPLICATION AND OPERATION. THE USER AND OPERATOR ARE RESPONSIBLE FOR CON

25 Figure 3-1. Battery Charger Location. Battery Charger Front Panel Battery Voltage and Charg

26 NOTE: (a) To maximize battery life, it is recommended that the factory supplied batteries be charged continuously for a minimum of 4 hours or un

27 Emergency Stop/Shut Down Button POWER OFF PUSH IN-To Engage Emergency Stop POWER ON TURN CLOCKWISE and RELEASE-To Reset Emergency Stop

28 Figure 3-2. Ground Control Station. (Machine Rear View) 1. Emergency Stop

29 Emergency Stop/Shut-Down Button POWER-OFF POWER-ON PUSH IN-To Eng

30 3. Move the joystick the desired direction of travel. TO STOP the machine return the joystick back to center. Elevating/Lower

31 3.7 PARKING MACHINE 1. Drive machine to a well-protected and well-ventilated area. 2. Ensure the platform is fully lowered, turn the main powe

32 3.9 FALL PROTECTION – LANYARD ATTACHMENT CAUTION THE MANUFACTURER RECOMMENDS THE OPERATOR IN THE PLATFORM WEAR A FULL BODY HARNESS WITH A LAN

33 3.10 QUICK-CHANGE PLATFORM MOUNTING SPM20 Model Lifts are equipped with quick-change platform mount, which allow quick removal and installation

34 3.11 TRANSPORTING, LIFTING AND TIE DOWN PROCEDURES General All SPM20 Series Model Personnel Lifts may be transported to a work site using the

35 NOTE: Lifting devise must be capable of handling the gross weight of the machine, see the Operating Specifications table at the beginning

EC DECLARATION OF CONFORMITY FOR MACHINERY MACHINERY: Powered Aerial Platform known as: Type: SPM20 E. C. Type Examinati

36 SECTION 4. EMERGENCY PROCEDURES 4.1 GENERAL INFORMATION This section explains the steps to be taken in case of an emergency situation during op

37 SECTION 5. GENERAL SPECIFICATIONS AND OPERATOR MAINTENANCE5.1 INTRODUCTIONThis section of the manual provides additional necessary information to t

38 Machine DimensionModelMax. platform heightMax. working heightRated loadThe number of persons allowed on platformPlatform size AxBStored dimension L

39 SPM 2 0 Machine Operating Area Electrical Specifications SPECIFICATION SPM20, System Voltage:

40 Platform DataSPECIFICATIONSPM20Occupants: (Persons allowed in Platform)1Maximum Work Load Standard:150kgPlatform Height – Mast Fully Extended– (Gro

41 Hydraulic Diagram (SPM20)

42 ITEM Table 5-1. – Lubrication Specifications KEY SPECIFICATIONS MPG- Multipurpose Grease having a minimum dripping point of 350 ° F. Excellent w

43 3 Swivel Raceways 2-Front Casters MPG-Pressure Gun √ 4 Mast Chains 2-Per Mast Section CL-Brush or Spray √ Inspect, lubricate if dry or

44 SECTION 6. INSPECTION AND REPAIR LOG Machine Serial Number: Table 6-1. Inspection and Repair Log Date Comments

45 Table 6-1. Inspection and Repair Log Date Comments

OPERATION MANUAL WARNING All personnel shall carefully read, understand and follow all safety rules and operating instructions before operat

46 BATTERY WARNING Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to caus

Local Distributor / Lokaler Vertiebshändler / Distributeur localEl Distribuidor local / ll Distributore localeEUROPE, MIDDLE EASTAFRICA & ASIAPHON

2 FOREWORD This manual is a very important tool! Keep it with the machine at all times. The purpose of this manual is to provide owners, users, op

3 SAFETY ALERT SYMBOLS ANDSAFETY SIGNAL WORDSThis is the Safety Alert Symbol. It is used to alert you to the potential personal injury hazards. Obey a

4 TABLE OF CONTENTS SUBJECT-SECTION, PARAGRAPH PAGE NO. FOREWORD ......

5 3.5 GROUND CONTROL STATION – OPERATION ............ 26 Main Power Key Switch ........